News:
Welcome to the Tormek Community. It is moderated by Jeff Farris. We have a new look, faster and more secure software under the hood, and much better spam controls to help eliminate garbage. If you previously registered for the discussion board but had not made any posts, your membership may have been purged. Secure your membership in this community by joining in the conversations.
www.tormek.com
| Subject / Started by | Replies / Views | Last post  |
||
|---|---|---|---|---|
|
|
TORMEK for Turners
Started by Jeff Farris |
0 Replies
5679 Views |
December 15, 2003, 08:49:45 pmby Jeff Farris |
|
|
Michelsen grind?
Started by turnedbykyle |
2 Replies
66 Views |
May 20, 2013, 06:13:39 am by turnedbykyle |
|
|
|
1 Replies
103 Views |
May 05, 2013, 04:23:40 pm by Ken S |
|
|
|
newbie to turning
Started by fraseman999 « 1 2 » |
24 Replies
403 Views |
April 23, 2013, 12:15:36 am by Rob |
|
|
|
Proper angle for a three point tool
Started by Dick Parman |
1 Replies
86 Views |
April 17, 2013, 01:45:14 am by Ken S |
|
|
|
Touch n turn feedback
Started by Rob |
13 Replies
393 Views |
March 29, 2013, 10:28:14 pm by Herman Trivilino |
|
|
|
17 Replies
2612 Views |
March 06, 2013, 01:56:39 am by Ken S |
|
|
|
|
SVS-50 and Diamond Parting Tool
Started by kcolenso |
5 Replies
665 Views |
February 17, 2013, 01:04:59 am by Jeff Farris |
|
|
|
How to sharpen bowl gouge as this link
Started by peterjones |
1 Replies
364 Views |
January 22, 2013, 09:13:03 pm by Rob |
|
|
|
2 Replies
572 Views |
December 31, 2012, 01:18:36 pm by Rob |
|
|
|
|
Alan Lacer skew
Started by Dick Parman |
6 Replies
673 Views |
December 31, 2012, 02:23:15 am by mski2 |
|
|
|
How to sharpen a ROUND skew ?
Started by toursiveu |
1 Replies
377 Views |
December 17, 2012, 06:56:33 pm by Jeff Farris |
|
|
|
sleeve position in gouge grinding jig
Started by Sergio |
0 Replies
396 Views |
December 04, 2012, 03:03:48 am by Sergio |
|
|
|
Sharpening a Raffan radius skew
Started by demps |
4 Replies
739 Views |
November 10, 2012, 12:03:11 am by demps |
|
|
|
T3 for infrequent turners?
Started by dustybob |
1 Replies
554 Views |
October 24, 2012, 03:28:41 pm by Jeff Farris |
|
|
|
2 Replies
890 Views |
October 09, 2012, 01:59:36 pm by Jeff Farris |
|
|
|
|
see posting in hand tools
Started by Ken S |
0 Replies
568 Views |
September 28, 2012, 11:46:10 am by Ken S |
|
|
|
1 Replies
787 Views |
September 26, 2012, 09:24:42 pm by Jeff Farris |
|
|
|
|
Setting the SVD-185
Started by TomC |
1 Replies
597 Views |
September 12, 2012, 03:19:37 pm by Jeff Farris |
|
|
|
Tormek Woodturner's Instruction Box
Started by GeekGirl |
3 Replies
830 Views |
August 09, 2012, 02:16:20 am by Ken S |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll