Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Grizz

Pages: [1] 2 3 ... 8
1
General Tormek Questions / Re: Multi Base-100
« on: August 09, 2018, 12:46:18 am »
I heard from Advance Machinery today. the lady quoted the new updated WM-200 will be available in October.
 Yes CB, I read that the add 18 degrees to the wm 200 will give you the right angle ! not a problem, just will be easier when we can get the updated version.

2
Knife Sharpening / Re: Sharpened / Photoshopped / Different Knife?
« on: August 09, 2018, 12:32:28 am »
cb, in my opinion, the knife on the right (the after shot) is wider than the (before) shot.
it may be possible that the after shot was actually the before shot, then the knife was mistreated on a nail and left in the rain about a month.

3
General Tormek Questions / Re: Multi Base-100
« on: August 06, 2018, 10:06:19 pm »
now if I could only find the updated WM-200 to assist with the side grinding !
I contacted Advance Machinery about it but haven't heard back yet. will let everyone know when I hear something.

4
General Tormek Questions / Re: Multi Base-100
« on: August 05, 2018, 02:33:26 pm »
I got a tracking number for the wheels and base yesterday ! wont be long now to try the new diamonds !

5
Knife Sharpening / Re: Beginner's questions
« on: July 28, 2018, 12:11:06 am »
good post Fernando !

6
General Tormek Questions / Re: Motor Shutting Down
« on: July 25, 2018, 05:00:46 am »
Jan and Ken, you are both correct, even tho the electromagnetic switches are not new technology, they are being used more and more in electrical motor environments as a safety feature.

7
General Tormek Questions / Re: Motor Shutting Down
« on: July 23, 2018, 11:57:35 pm »
Jan, you are correct. the T-8 also has a magnetic switch, meaning if power is lost it will not automatically come back on when power is restored. must press the start switch again.

8
Knife Sharpening / Re: Frontal Vertical Base
« on: July 17, 2018, 11:33:11 pm »
you will love it, simply because "it works".

9
I truly believe in the Tormek grader and still use the grader on all but the SJ-250

For the SJ stone, I too use the Wootz method of the 1000 grit diamond plate to not only clean the SJ, but to grade it as well. I primarily started using it just to clean the wheel, but soon discovered an exciting anomaly that it IMO re-grades the SJ to a higher grit level. of course I cannot prove this actually happens, but the wheel seems twice as slick after the diamond plate has been on the wheel only a minute or two.

10
General Tormek Questions / Re: Tormek stone grader
« on: July 17, 2018, 02:04:06 am »
to answer Wolfy questions: I wonder how many use the stone grader and how often?

What is others experience?

I started using the stone grader when I bought the T-8 about 5 months ago. I learned by watching Stig and Jeff Farris. they both do a great job teaching. that leaves "experience". I started using and refining their techniques and now use it every time I need to cleanup or re-grade the SG-250. The Tormek grader has served me well and still looks almost new due to following Stig and Jeff techniques and advice.

 As far as my SJ-250, I usually clean after use with the rust erasers, which do a fine job. I didn't think the SJ-250 actually needed grading, but after watching Wootz video's, I decided to use the diamond plate approach. With the help of Ken and a little luck, I put together a great way to grade the SJ-250 with the diamond plate.

 IMO, it is very important to use the stone grader's of either or both methods to improve your stones and your level of sharpness !

11
General Tormek Questions / Re: Rust eraser...
« on: July 13, 2018, 04:13:28 am »
I've used them for a couple years now. I really like them. does work wonders for cleaning the stones.

12
same here Ken. ! :)

13
General Tormek Questions / Re: Truing Tool Diamond Cutting Tip
« on: July 12, 2018, 02:13:42 am »
I agree with jeff, if only 5 of 17 are working satisfactorily then no big problem.

14
Knife Sharpening / Re: best Tormek knife sharpening video
« on: July 11, 2018, 12:07:41 am »
you will like the new FVB. I've had mine about two weeks now. (check your mail Thursday)

15
Knife Sharpening / Re: T4 vs T8 grid hollownes
« on: July 09, 2018, 11:25:35 pm »
I chose the T-8. its a little larger and has an unlimited run time without a cooling down period. better motor in my opinion.

Pages: [1] 2 3 ... 8