Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Al

Pages: [1] 2
1
Knife Sharpening / Re: Bevel battle - help please
« on: November 29, 2020, 09:59:27 pm »
I noticed that you have your knife jig quite close to the heel.I would move the jig so it’s more central

2
Knife Sharpening / Re: Paper wheel
« on: August 26, 2020, 09:42:30 am »
I follow the procedures of Knife Grinders (Australia)

For new paper wheels I apply the diamond paste after ever 5-10 knives used on the wheels but first I apply a thin layer of chainsaw oil to help bind the diamond to the wheels. I apply the chainsaw oil once to the virgin wheels

I do this for the first 3 months then after that I re apply the diamonds after I’ve done around 50 knives

After a few hundred knives the wheels will get a good build of diamonds

Vadim suggests a bit of parraffin Oil if the blades are starting to look a bit warn before you reach the 50
mark
Always apply the diamond paste at the end of the day so it can settle in overnight

 Always keep the slots clean, this will help cool the wheels, I use a piece of dental floss, works a treat, just don’t use the same piece on your teeth....🔪

3
Knife Sharpening / Re: Grinding software upgrade is coming
« on: March 30, 2020, 11:51:35 am »
Have heard from Wootz managed to get all my apps working a treat .things have been quite slow down here in NZ with Covid 19 putting our whole country in lock down for at least a month

4
Knife Sharpening / Re: Grinding software upgrade is coming
« on: March 17, 2020, 06:22:42 pm »
I am having problems with the 3 apps opening
Have just gotten a new laptop and can’t open any of them. I too think I need the activation pin from knife grinders. Have emailed them about this issue but haven’t heard anything in the last few weeks. Wootz must be run off his feet!
Very unusual as he is usually really prompt

5
Knife Sharpening / Re: Frontal Vertical Base
« on: June 25, 2019, 08:34:01 pm »
Here here. Ditto from me Ken.
It’s an absolute must and I’m always happy to support Wootz.
Sub 50’s on the Bess would never have been possible for me without these aids and Wootz generosity in sharing his knowledge

6
Knife Sharpening / Re: protective paper in the knife jigs
« on: June 25, 2019, 08:28:36 pm »
I use both the Norton Bear and also duck tape
To protect the handles I have a 100mm (4”) roll of shrink wrap packaging plastic
The shrink wrap and handle applicator was around $8 NZ Works well as if you stretch it while wrapping its tight on the knife

7
Knife Sharpening / Re: Mobile knife sharpening using the Tormek
« on: June 20, 2019, 09:59:49 am »
Nice set up Mat!

8
Knife Sharpening / Re: Advice for 10 inch paper wheels
« on: May 27, 2019, 11:56:59 pm »
Just a note on the grinder
Most flanges on grinders that hold the wheels are just pressed steel and useless
You will need to get some solid steel ones turned up
I got a local engineer to do this for me after Wootz told me about this

9
Knife Sharpening / Re: Advice for 10 inch paper wheels
« on: May 27, 2019, 11:50:26 pm »
Yes you are correct
Wootz supplies all the mounting information

10
Knife Sharpening / Re: Advice for 10 inch paper wheels
« on: May 27, 2019, 08:36:01 pm »
Hi Antz
Welcome to the forum
You may be able to get a Palmgren-9682107 8” Variable speed grinder and I think Jet also does a variable speed one although the jet is more expensive
We have the same problem in New Zealand basically zip low speed grinders
I was about to import a Palmgren but managed to find a Macma 10” buffer with 2 speeds the low one being 1750 rpm. Even though it is 10” the shaft protrudes well past the motor housing (200mm) and the wheels are 50 mm higher than the housing
Wootz configured the supports to suit this machine and with his software I’m getting exceptional results
Keep us informed with what you end up doing

11
PayPal good for New Zealand

12
I also have emailed my interest and look forward to future development

13
Knife Sharpening / Re: Proper Maintenance of a Knifes Edge
« on: April 27, 2019, 06:45:37 am »
Another thing with end grain boards is the glue used in them. Some resorcinol and epoxys are harder than others and could affect the edge of the knives although I would imagine this would be minimal. Quarter cut boards have a straighter grain than crown cut but I don’t know if this would have any adverse effects.In cabinetmaking which was my job for the last 40+ years chisel blades always stay sharper for longer when used with the grain rather than across the grain.I also will be following Vadim’s research with interest

14
Humm you got me thinking with your comment “with the right set up of the paper wheel supports you should be there already “ re checked the constants on your paper wheel angle setter app and had put the left wheel vertical 74.8 on the right wheel and the right vertical 73.3 on the left. Small discrepancy I know but nonetheless may make a difference

15
Knife Sharpening / Re: Tormek SG & leather wheel - razor sharp
« on: April 21, 2019, 11:37:13 pm »
Yes that’s correct 1st honing was at 10 dps. 1 pass each side then repeat 1 more pass each side. The Bess at this stage from memory was around 180.then did 1 more pass each side at 11.5 dps and the Bess was 65. This result was all due to the patience of Wootz answering all my questions

Pages: [1] 2